AIzaSyBMJLehm8j6j0La8w7yFA5HiR9WVNS8rHc

Technical Data Sheets

Safety Data Sheets

Finish

85° = < 10.0. Sheen levels depend on porosity and various surface irregularities.

Best for use in

Small paint projects and spot priming interior surfaces including wood, drywall, plaster, paneling, wallpaper, masonry, brick, painted metal and properly prepared glossy surfaces.

Coverage

1.9 - 2.3 m2 per container, depending on the surface texture, porosity and application method. It does not include the loss of material from spraying.

PRODUCT USAGE
  • This convenient aerosol is ideal for small paint projects and spot priming interior surfaces including wood, drywall, plaster, paneling, wallpaper, masonry, brick, painted metal and properly prepared glossy surfaces†.
  • Not recommended for mold or mildew-prone surfaces or flooring.

Surface Preparation†

  • The surface must be clean, free of dust, grease, wax, peeling paint, mold, mildew, and/or wallpaper paste. If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and allow to dry.
  • Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.*
  • †Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before priming.*

Read More

Application

  • Eye protection is recommended.
  • For best results, use when substrate and air temperatures are between 2 °C and 32 °C.
  • Cover adjacent areas to protect from overspray.
  • Shake can vigorously for 1 minute after mixing ball begins to rattle and often during use.
  • Hold can upright, moving from side-to-side while spraying lightly and evenly about 30 cm from area being painted.
  • Two to three thin coats produce best results.
  • Topcoat with latex or oil-based paint after 1 hour.
  • Dries to the touch in 30 minutes at 25 °C and 50% humidity.
  • Finishing: Topcoat within 30 days to prevent contamination of the primer before painting.
  • NOTE: On some surfaces, spot priming may cause a non-uniform appearance in the final coat. To avoid this, prime the entire surface.

Read More

Dry Time at 25°C, 50% RH

  • To Touch: 15 -30 Minutes
  • To recoat / Topcoat: 1 Hour
  • Longer dry time may be required in cooler temperatures and higher humidity.

Read More

Clean-Up & Disposal

  • Clear spray valve immediately after use by turning can upside down and spraying until only clear gas is released.
  • If spray nozzle becomes clogged, remove and clean. Do not stick pins or wire into can opening.
  • Replace nozzle with valve opening pointed away from you.
  • Clean fresh overspray with mineral spirits or paint thinner. Remove dried paint with paint remover, but test small area first to ensure paint remover does not damage substrate.
  • Please consider donating any unused product.
  • For recycling or disposal information, contact your local household refuse collection service.
  • To consult with a KILZ Certified Coatings Professional, call 1-866-PRIMER-1 (U.S.A. only).

Read More

Read More

WARRANTY

Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Quebec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Masterchem Industries LLC unless extended by a provincial consumer statute. To obtain warranty service, write to: Technical Services, Masterchem Industries LLC, 2750 Centre Avenue N.E., Calgary, AB T2A2L3, or email: techserve@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

Read More

Reviews

Pro Contractor wearing a cap and shirt with Behr

PAINTING CONTRACTORS

Professional products and services specifically designed for residential and commercial painting contractors.

FOR CONTRACTORS
A small image of a Property Manager showing a BEHR PRO Rep a multi-family complex. The property manager is pointing at something while the BEHR PRO Rep is looking at what she is pointing and taking notes on a laptop.

PROPERTY & FACILITY MANAGERS

A full range of products and services to help property and facility managers enhance and maintain the appearance of properties.

FOR PROPERTY MANAGERS

READY TO GET STARTED?

Contact a Behr Pro Rep Icon

CONTACT A BEHR PRO® REP

Your reputation depends on your ability to do the job right. BEHR can help.

Find a rep
Technical Services Icon

TECHNICAL SERVICES

1-800-661-1591
Mon - Fri, 6am-3pm PST
Sat. & Sun., Closed

PRO XTRA logo

JOIN THE HOME DEPOT® PRO XTRA LOYALTY PROGRAM

Get 10% - 20% Back in Quarterly Rewards
BEHR® Paints, Stains & Primers.

sign up on homedepot.ca