BEHR PRO® Block Filler Primer No. PR50
BEHR PRO Block Filler Primer is a dependable solution for above-grade concrete surfaces, such as concrete block, cinder block, and poured or pre-cast concrete. It is an interior/exterior primer formulated to fill and seal porous masonry surfaces, reduce pin holing and provide a smooth surface prior to finish coat application.
Safety Data Sheets
Best for use in
Interior and Exterior
Coverage
7-9 m2 per 3.79 L
- Use on properly prepared, above-grade interior or exterior surfaces, such as concrete, concrete block/CMU, brick, cement board siding, stucco, and plaster.
Surface Preparation
- The surface must be clean, free of dust, grease, wax, peeling paint, mold, mildew and release agents. If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and allow to dry.
- Fill all gaps with paintable sealant and allow to completely dry prior to coating.
- For maximum adhesion, glossy and slick surfaces must be de-glossed prior to coating.
- This product is only designed to be used on unpainted masonry surfaces that have been allowed to cure(dry) at least 30 days with a moisture content below 15% before application.
- Do not apply to shiny or slick surfaces or loss of adhesion may occur; these surfaces can be prepared with chemical etchers and/or sandblasting.
- Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming.
Read More
Application
- Eye protection is recommended.
- Use only when temperatures are between 10°C and 32°C.
- Stir thoroughly before and occasionally during use. Apply using a brush, roller or spray.
- For best results apply 2 coats and apply with airless sprayer. Backroll each coat working the material into the surface filling the masonry pores and voids.
- Prime the entire surface to ensure a uniform appearance of the topcoat.
- May be tinted with up to 2 ounces (59 ml) of universal colourant per gallon.
- For airless spray applications, tip size should be .019 - .025.
Read More
Dry Time
- Dries to touch in 1hour at 25°C and 50% humidity. Application at lower temperatures, high humidity or poor ventilation will affect dry time.
- Recoat or topcoat after 2 hours.
- Full Cure: 7 Days
Read More
Clean Up & Disposal
- Clean equipment and paint splatters with warm, soapy water. If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations.
- Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.
Read More
To consult with a Behr Company Representative, call 1-800-661-1591.
Read More
Read More
WARRANTY
For one year from the date of purchase, Behr Process LLC warrants to the original consumer purchaser, (1) that the product meets Behr Process LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. If this product is found not to perform as specified on the label within one year from the date of purchase, Behr Process LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. THIS WARRANTY EXCLUDES (1) LABOUR AND COSTS OF LABOUR FOR THE APPLICATION OR REMOVAL OF ANY PRODUCT, AND (2) ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON BREACH OF EXPRESS OR IMPLIED WARRANTY, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER LEGAL THEORY. TO THE EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process LLC unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-661-1591, or contact Behr Process LLC at 110-600 Barlow Square S.E., Calgary, AB T2C 5T7. Behr Process LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
Read More
Reviews
PAINTING CONTRACTORS
Professional products and services specifically designed for residential and commercial painting contractors.
FOR CONTRACTORS
PROPERTY & FACILITY MANAGERS
A full range of products and services to help property and facility managers enhance and maintain the appearance of properties.
FOR PROPERTY MANAGERSREADY TO GET STARTED?
CONTACT A BEHR PRO® REP
Your reputation depends on your ability to do the job right. BEHR can help.
Find a rep
JOIN THE HOME DEPOT® PRO XTRA LOYALTY PROGRAM
Get 10% - 20% Back in Quarterly Rewards
BEHR® Paints, Stains & Primers.
About Interior Paint Sheens
Get the look you want and the protection you need for any room in your home.
A flat sheen has a non-reflective finish that touches up well and hides minor surface imperfections.
Low-traffic areas; interior walls and ceilings
Ceilings
Medium-Low
A matte sheen has a low-luster, reflective finish that is durable, easy to clean, touches up well and also hides minor surface imperfections.
Low-traffic areas; interior walls
Family rooms, living rooms, kids' rooms, bathrooms, dining rooms, ceilings
Medium
An eggshell enamel sheen has a soft, velvety appearance that resists dirt and grime, as well as mildew.
Moderate-traffic areas
Family rooms, living rooms, bedrooms, kids' rooms, hallways, dining rooms
Medium
A satin enamel sheen has a pearl-like finish that's easy to clean.
All interior surfaces; moderate- to high-traffic areas
Family rooms, living rooms, bedrooms, kids' rooms, hallways, kitchens, bathrooms, doors, windows, trim, cabinets, shutters, interior furniture
Medium-High
A semi-gloss enamel sheen is sleek and radiant resisting mildew, moisture and wear.
Cabinets and trim; high-traffic, high-moisture areas
Kids' rooms, hallways, kitchens, bathrooms, doors, windows, trim, cabinets, shutters
High
Hi-Gloss enamel sheens provide have a brilliant, shiny appearance and a durable, glass-like finish that allows dirt and grime to be wiped clean.
High-use surfaces
Kitchens, bathrooms, doors, windows, trim, cabinets, shutters, interior furniture
High
About Exterior Paint Sheens
Set the right curb appeal with exterior painting efforts that last.
A flat sheen is non-reflective, and easy to apply and touch up. It will minimize the appearance of minor surface imperfections.
Wood and vinyl walls and siding; brick and other masonry; fences
Medium-Low
A satin enamel sheen creates a pearl-like finish that's durable and dirt-resistant. It will also resist moisture, fading and stains.
Virtually all exterior surfaces
Medium-High
A semi-gloss enamel sheen is sleek and radiant with a hard, durable finish. It is formulated to withstand wear, and will also resist moisture, fading and stains.
Doors, trim and shutters; Exterior furniture
High
Hi-Gloss enamel sheen have a brilliant, shiny appearance and a durable, glass-like finish that allows dirt and grime to be wiped clean.
High-use surfaces
High
- Free Same-Day, Next-Day Delivery*
- Call, Text, or Email Your Paint Order
- Will Call & Schedule Deliveries
- Custom Color Matching
- Product & Record Order Management
- Expert Paint Knowledge
- Free Same-Day, Next-Day Delivery*
- Call, Text, or Email Your Paint Order
- Will Call & Schedule Deliveries
- Custom Color Matching
- Product & Record Order Management
- Expert Paint Knowledge
- Get 10%-20% back in quarterly rewards on BEHR® Products when you join Home Depot's Pro Xtra™ loyalty program
- Call, Text or E-mail your orders to your dedicated BEHR PRO Paint Specialist
- Arrange will call & Schedule Deliveries for pick-up at your Home Depot location or for delivery to you
